DIY - Passat CC Replace Rear Brake Pads (EPB).

Hi everybody, Today i will show you step by step how to Replace rear brake pads on Passat CC, Electronic Parking Brake (EPB), We are updating this page now, pic, video, etc...

Requirements:

1. Battery charger, if you don't have a Battery charger There's always Plan (B), Learn How.
2. 15mm wrench.
3. 13mm socket.
4. VCDS program, It is necessary to save a complete Auto-Scan before repairs.
5. Clamp

Step # 1: Remove both rear wheels.
Step # 2: Connect a Battery charger before you start the caliper opening, Read More.
Step # 3: Now we  have to open rear parking brake using VCDS program

---

VCDS Open Rear Parking Brake
Prerequisites:

• Connect a battery charger as per repair manual.
• Ignition on, engine off.
• Cycle the Parking Brake ON, then OFF first.

[Select]

• [53 - Parking Brake]

[Basic Settings - 04]

• Group 007

[Go!]

Activate the Basic Setting.

[ON/OFF/Next]

The brake pads are now opening.

You will hear the rear caliper motors working, wait 30 seconds after the brakes stop moving before carrying out the next step.

---

Step # 4: You are ready to remove the calipers Using both 13mm socket &15mm wrench.

Step # 5: Remove the old pads and install the new pads.

Step # 6: Make sure you open your brake fluid reservoir, Now push piston back on caliper using clamp.

Step # 7: Put the caliper back onto the carrier, Reattach the bolts.

Step # 8: Now we  have to close rear parking brake using VCDS program.

---

VCDS Close Rear Parking Brake

Prerequisites:

• Connect a battery charger as per repair manual.
• The Parking Brake must be OFF before Basic Setting are possible.

[Select]

• [53 - Parking Brake]

[Basic Settings - 04]

• Group 006

[Go!]

Activate the Basic Setting.

[ON/OFF/Next]

The brake pads are now closing.

---

Step # 9: Now we  need to test the parking brake using VCDS program.

VCDS Function Test

Prerequisites:

• Connect a battery charger as per repair manual.
• The Parking Brake must be OFF before Basic Setting are possible.

[Select]

• [53 - Parking Brake]

[Basic Settings - 04]

• Group 010

[Go!]

Activate the Basic Setting.

[ON/OFF/Next]

The brake pads are now opening and closing 3 times.

Important: Wait 30 seconds after the brakes stop moving before carrying out the next step.

[Done, Go Back]

[Close Controller, Go Back - 06]

---

Step # 10: The final step, close down VCDS Program and disconnect the battery charger, put your wheels back, Close the brake fluid reservoir, NOW Let's Go Test Drive.

---

Copyright © 2013 Fredj Fix Blog. All Rights Reserved.

DC 2000 / DC 2000 PVR Upgrades via USB

Update 12-03-2013 / 12:26:00, New DC 2000 / DC 2000 PVR Firmware Upgrades via USB Port 2, Works with Eutelsat W3 (7.0E).

Important quotes: The lastest firmware is here click on the link below, It work just perfect so far, if you're looking for OSN | Orbit Showtime Network, forget it don't try watch any channel that using betaCrypt coding. .

enjoy it!

• Software
• Guide
• Cable Pin
• Cable USB
• Loader
• Flash File
• Troubleshooting Information
• Tools
• Upgrades

Download page.

Guide - How to Upgrade the DC 2000 PVR and DC 2000 Firmware?.

---

Copyright © 2013 Fredj Fix Blog. All Rights Reserved.

Guide - How to Upgrade the DC 2000 PVR and DC 2000 Firmware?

Step #1 Download the lastest firmware click the link below

DC 2000 / DC 2000 PVR Upgrades via USB

Step #2 Install

Download and Save It in a USB flash drive. Insert the  USB Flash drive on the back USB port and press MENU button on your remote control then go to USB and Look for the file named “2013xxxx_DC2000_SUB_USBLOCK_RE_Vxxx.bin”

Step #3  Activate your new software.

Step #4  Press MENU and press “9999”, a menu will appear. You have to set everything's to “YES”.

---

Copyright © 2013 Fredj Fix Blog. All Rights Reserved.